Main data

• Polymer housing/ three conduit entries
• Protection degree IP53 or IP65
• Various contact blocks available
• Variouis auxiliary device available
• Assembled through special joining kits

General data

• Ambient temperature: -25 to +80 C
• Max actuation frequency: 3600 operations cycle/hour
• Mechanical endurance: 20 million operations cycle

Rope Pull Switches

• Models that comply with cable break/slack detection with manual reset for Emergency Stop applications
• Available spans range from 6 to 100 m
• Trip and latch switch models are available
• Minimum switch life is 1-million operations
• Heavy-duty switch housings withstand harsh environments and outdoor use
• Switch activates if the rope is pulled, becomes loose or breaks
• Design meets positive opening requirements for rope pull switches (IEC 60947-5-1)
• RP-RM83 and RP-LS42 comply with ANSI NFPA 79, ANSI B11.19, IEC 60204-1, EN 13850 and EN ISO 60947-5-5 for Emergency Stop applications
• RP-QM72/QMT72, RP-LM40 and RP-QM90 comply with ANSI NFPA 79 and IEC 60204-1 for Stop Control applications

• Cable break/slack detection with manual reset
• Manual reset (Latch) design
• Heavy-duty housing to withstand harsh environments and outdoor use; IP67 rated
• Rope span up to 75 meters
• E-stop button with manual reset
• Tension indicators
• Additional solid-state auxiliary output for remote tension monitoring
• Extra contacts for switch monitoring
• 90 mm wide at base
• Rugged metal housing with protective earth terminal (IEC 60947-1)

รายละเอียดเพิ่มเติม Click!!

• Cable break/slack detection with manual reset
• Manual reset (Latch) design
• Rope span up to 75 meters
• Model with E-stop button for manual reset
• Quick rope fixing and tensioning
• Tension indicator
• Extra contacts for switch monitoring
• 42 mm wide at bAase
• Insulated device (IEC 60947-5-1)

รายละเอียดเพิ่มเติม Click!!

• Manual reset (Latch) design
• Rope span up to 6, 12 or 20 meters
• Tension Indicator
• Models with additional contacts for monitoring or dual channel hookup
• 82 mm wide at base
• Rugged metal housing with protective earth terminal (IEC 60947-1)
• Cable break/slack detection (note: does not comply with manual reset requirement per EN IEC 60947-5-5 for Emergency Stop applications.)

รายละเอียดเพิ่มเติม Click!!

• Manual reset (Latch) and Auto Reset (Trip) models
• Rope span up to 6 meters
• Tension Indicator
• Limit-switch style housing (EN 50041)
• 40 mm wide at base
• Rugged metal housing with protective earth terminal (IEC 60947-1)
• Cable break/slack detection (note: does not comply with manual reset requirement per EN IEC 60947-5-5 for Emergency Stop applications.)

รายละเอียดเพิ่มเติม Click!!

• Manual reset (Latch) design
• Rope span up to 100 meters, with switch in center
• Manual reset
• Extra contacts for switch monitoring
• 90 mm wide at base
• Rugged metal housing with protective earth terminal (IEC 60947-1)
• Cable break/slack detection (note: does not comply with manual reset requirement per EN IEC 60947-5-5 for Emergency Stop applications.)

รายละเอียดเพิ่มเติม Click!!

Tel: 02 10 50 555

• Controller monitors up to 22 inputs for proper operation
• Each input can be configured for Control Reliability for Category 2, 3 or 4 safety circuit performance per OSHA/ANSI or ISO 13849-1, or for a non-safety input
• Input terminals can monitor both contact-based or PNP solid-state outputs 3 pairs of solid-state safety outputs with ON-Delay, OFF-Delay and cancel OFF-Delay
• 10 configurable auxiliary status outputs track inputs, outputs, lockout, I/O status and other functions
• SC22-3E models provide diagnostic information using EtherNet/IP, Modbus TCP and PCCC
• Configuration is extremely intuitive with the built-in front panel LCD display or using a PC Interface (download free at www.bannerengineering.com/sc22)
• Controller can be configured offline using a PC; replicate configuration to memory card, email or export as PDF or DXF files
• Controller is designed to meet stringent standards including Safety Integrity Level
  (SIL) 3 per IEC 61508, SIL CL 3 per IEC 62061 and Category 4 Performance Level
  (PL e) per EN ISO 13849-1

• 22 input terminals for monitoring of both contact-based or solid-state outputs from Banner devices or any other
  manufacturer
• Three pairs of independent solid-state safety outputs
• Configurable auxiliary outputs for tracking inputs, outputs, lockout, I/O status and other functions
• Reduces the complexity of interfacing multiple safety functions and devices

      รายละเอียดเพิ่มเติม …CLICK!!

• Monitors contact failure or wiring fault
• Self-monitors to eliminate risk if module fails
• Installs easily

      รายละเอียดเพิ่มเติม …CLICK!!

• Monitors contact failure or wiring fault
• Used with one or two solid-state PNP or hand/relay contact safety or non-safety devices

      รายละเอียดเพิ่มเติม …CLICK!!

• Monitors a single mat or a series of connected mats
• Used with any standard 4-wire safety mat or edge triggered by a short in a contact plate or strip

      รายละเอียดเพิ่มเติม …CLICK!!

• Suspends safeguarding during hazard-free times in the machine’s cycle
• Allows material to move into or from the process, without tripping the primary safeguard
• Monitors two or four hard-relay contact safety devices

      รายละเอียดเพิ่มเติม …CLICK!!

• Monitors two sensors with PNP outputs for rotation and linear movements
• Allows safety switches to release and safety gates to be opened when the speed drops below the dangerous level

• Provides additional safety outputs for a primary safety device with relay outputs
• Offers two hookup options, depending on model: one channel, or one or two channel
• Models with stop category 1 (OFF Delay)

      รายละเอียดเพิ่มเติม …CLICK!!

• Increases the switching current capacity of low voltage primary safety devices to 6 amps
• Serves as a relay for primary safety devices with solid-state or hard contact outputs and external device monitoring

Tel: 02 10 50 555

• Magnet switches for non-contact applications
• Compact, 3-piece non-contact system
• Sealed to resist water and dirt
• Designed to resist intentional defeat

      รายละเอียดเพิ่มเติม…CLICK!!

• Load-bearing, lever and rotating hinge styles
• Adjustable range of operation
• One-piece switches

      รายละเอียดเพิ่มเติม…CLICK!!

• Designed to minimize tampering
• Five actuator types
• Actuator engagement from different locations

      รายละเอียดเพิ่มเติม…CLICK!!

• Rigid and flexible in-line actuators
• Rotating actuator heads

      รายละเอียดเพิ่มเติม…CLICK!!

• Two options for locking mechanisms
• Two models for different voltages
• Rigid and flexible in-line actuators
• Rotating actuator heads

      รายละเอียดเพิ่มเติม…CLICK!!

Tel: 02 10 50 555

• Two-dimensional laser scanners effectively protect personnel, as well as stationary and mobile systems within a user designated area
• Persons or objects entering the protection field will be detected and a protective (safety) stop signal will be generated
• Eight protective and warning field pairs are individually defined using a PC
• Protective field can be set from 200 mm to 6.25 m with a resolution of 30 to 150 mm
• Available with 4 or 6.25 m maximum protective field range
• The warning field range can be set for up to 15 m with a resolution of 150 mm
• Scanner has a 0.36° lateral resolution and detects objects in a 190° working zone
• Two solid-state OSSD safety outputs (250 mA) and two solid-state auxiliary
  outputs (100 mA)
• The highly flexible protective and warning fields can be set to match the shape of the work area
• Exceeds OSHA/ANSI Control Reliability requirements, certified to cTUVus, and CE certified to Type 3, Cat 3 PLd, and SIL 2
• Response time is 80 milliseconds (default), adjustable to 640 milliseconds
• Compact design, simple installation and easy-to-use software provide efficient integration into work areas
• Rugged, die-cast aluminum housing withstands the rigor of factory floors
• 5-LED display presents system status and diagnostics of devices without the need for a PC connection

AG4-TB1 Test Box

With the test box it’s possible to test the following Scanner functions without hooking it up to the machine interface:

• Switch over between the different field pairs
• Indication of the Safety OSSD outputs (when entering protective field)
• Indication of the Alarm outputs (when entering warning field)
• Can be used as a “cloning” device to load the same configuration into multiple scanners
• Machine Interface-to-Test Box cordset included
• Power supply not included

AG4 Safety Laser Scanner Kits

You can purchase a kit that contains a laser scanner, optional interfacing solutions and cordsets.
To Order:
1. Choose an optional interfacing solution, such as an UM-FA-
9A or -11A universal input safety module.
2. Choose a DB15 machine interface cordset, such as AG4-
CPD15…
3. Choose a PC communication cordset, such as AG4-PCD9…

Tel: 02 10 50 555

Tel: 02 10 50 555

E-Stop Button
Emergency Stop Push Buttons

• Electromechanical palm buttons push to stop and twist to release.
• Modular design makes assembly and installation easy.
• Kits simplify selection and ordering.
• Latching design complies with ANSI NFPA 79, IEC 60204-1 and ISO 13850 (EN 418); direct positive opening operation per EN/IEC 60947-5-1
• Options include station enclosures, contact elements and disc labels.

Tel: 02 10 50 555